Profile Photo
Tom Cleaver
908 articles

Eduard 1/48 Spitfire XVI “lowback”

May 7, 2016 · in Aviation · · 4 · 1.4K

The XVI is a Mk. IX airframe with a Packard-built Merlin-266 engine. The type began production in the fall of 1944; however, delivery delays by Packard resulted in the type not becoming operational until late 1944. The “lowback” version, which was first developed in the fall of 1944, was not delivered to squadrons until march 1945 due to these delivery delays.

The type was optimized for low-level operation, and was employed primarily in ground-attack in the final stages of the war in northwestern Europe. Following the end of the war, the Spitfire XVI equipped most of the RauxAF squadrons. By 1952, it was the most-common wartime aircraft left in Britain, and sixteen of them were used in place of Hurricanes in the motion picture adaptation of Paul Brickhill's biography of Douglas Bader, “Reach for the Sky.”

's “low back” Spitfire XVI is the third kit of this sub-type to appear in scale, following a kit released some 15 years ago by ICM and one a few years back by Ocidental now boxed by Italeri. As with all the other Eduard Spitfire releases, it can be considered “definitive” in terms of overall accuracy and quality of production.

Eduard's release of the “dual combo” kit allows a modeler to build both a “high back” and “low back” Spitfire XVI. A plus in the kit not available in later releases of the “lowback” version by itself is that there are upper wing parts for both the “early” version without the bulge over the main gear well, and for the “late” version with this. Separate wheels and hubs are provided for both types. The single-kit “Profipack” and “Weekender” releases only include the later upper wing.

Decals are provided for six aircraft, three of each sub-type, printed by Cartograf. Since this is a “Profipack” release, photo-etch details are also included for the instrument panel, seat belts, and other fine details.

Construction of the Eduard Spitfires is “fiddly” due to what I think of as “over-design” of details like the wheel wells. The secret to building an Eduard Spitfire is to thoroughly clean up all parts once removed from the sprue, to remove sprue connection points, and to be careful in assembly of sub-assemblies. If you do this, the only place you will need any seam filler is with the upper cowling part (why this wasn't produced as one part as it should have been is beyond me).

Past that, assembly of the kit is the same as any other Eduard Spitfire kit. With care, you will not need putty anywhere, but you must clean up the parts because fit is very precise.

After painting the leading edges of the outer wings yellow and masking that off, I freehanded the camouflage using the Tamiya RAF colors: RAF Ocean Grey, RAF Dark Green, and RAF Medium Sea Grey. Once dry, I gave the model a coat of clear Gloss.

I applied all the stenciling decals first, then applied the markings for the boxart option, the Spitfire XVI operated by 443 Squadron RCAF in 1945-46. The decals went down without problem under a coat of Solvaset.

I attached the landing gear and prop, unmasked the canopy and attached the bubble in the open position.

Eduard's Spitfires are deservedly considered the best kits of the Merlin-60 series Spitfires available. They are a solid step up from any other similar kit. Any modeler who takes their time in assembly and finish of the kit is assured of a beautiful model. Highly recommended.

Reader reactions:
2  Awesome

10 additional images. Click to enlarge.


4 responses

  1. Great job, now I'm inspired to build a Spit.

  2. Profile Photo
    P.k said on May 8, 2016

    Nice paint and build LIKE!

  3. Another great-looking model, Tom! Where do you have time to both build and write, all the while still having to eat, sleep, etc?

Leave a Reply