Profile Photo
David Kopielski
67 articles

Repairing, Cleaning, and polishing clear parts and canopies.

March 22, 2020 · in How-to · · 5 · 4.9K

I have had a few requests on how I get my canopies so clear looking. Many times the clear parts in kits can get scuffed in shipping if they are not protected or come loose. Also some jet canopies or bubble top aircraft can have a seam from the injection molding process that runs down the centerline of the canopy.
Some folks like to dip the canopies and clear parts in Pledge Future. I prefer to polish them and feel they look better and much clearer. To start with, many vehicles today have a clear plastic cover over the headlights. Over time and driving in the elements the plastic gets foggy and starts to yellow. There are many products on the market to clean them up. These products also help us modelers as well. I have tried many products and found one that works very well on the clear styrene plastic used on the models we build. The product I use is made by Meguire’s, a company that makes many products to keep your vehicle clean, shiny and protected. The product they make is called PlastX. It is a cleaner and polish for plastic parts.
So the first part I have a clear nose for a 1/48 Monogram B-17G. The kit was bought at a goodwill store and has all the sprues loose in the box. This has caused some scuffs on the nose. The first step is to take a small dish and put a couple of drops of the PlastX on it. Then using a cotton swab I dip in the PlastX and in a circular motion I scrub and polish the affected areas then I polish the rest of the nose inside and out. After a few moments I let it dry a few minutes then use a microfiber cloth and polish and wipe clean the part. You can see the before and after photos below.

For removing the seams on canopies the first step is sanding down the seam with 600 grit sandpaper. Only sand a small strip where the seam is. Once the seam is gone, the next step is to use 1000 grit sandpaper and sand in a slightly wider area than you did in the previous step. Then the next step is to wet sand with 2000 grit sandpaper in a wider section. The reason is this prevents any distortion where you removed the seam. Then as similar to removing scuffs, the PlastX is applied with a cotton swab.
The area that was sanded is cleaned and polished for a minute or two and then a quick polish of the inside and out of the canopy is done. Let dry a few minutes then polish with a microfiber cloth.
While it is difficult to see in the photos, the canopy looks clearer and has more shine to it. I typically run a quick polish over clear all the parts even if there is no visible scuffs as once polished they much are clearer and shine better.
You can check out all my other tips at https://davidsscalemodels.com/tips-and-tricks/

Reader reactions:
8  Awesome

8 additional images. Click to enlarge.


5 responses

  1. Thanks for the info, David,
    All the best!

  2. Thanks David, I always thought car maintainence products were a bit too heavy duty but I will give it a go after seeing this.

  3. just realize some of those seams belong on the centerline of the canopy as the one captured on the tamiya f-14 is some kind of antennae or defroster and belongs there

    1 attached image. Click to enlarge.

  4. Another product that is great for canopies and other clear parts is the Novis plastic polish system. Available In 3 numbered bottles and designed to be used in descending order or you can purchase each bottle individually. #3 is for heavy scratch removal. #2 for fine scratches. #1 is plastic cleaner and final polish. I use #2 the most. Highly recommended.

  5. I use Meguiars products on my full sized 1 to 1 scale restoration work. They have a great plastic polish too.

    I read this article on your website. You have a lot of great stuff posted over there. Thanks for sharing this with us.

    Stay safe.

Leave a Reply